ANDIO, RAHMAN (2016) PENILAIAN RISIKO PEKERJAAN PADA DIVISI PIPA MENGGUNAKAN METODE JOB SAFETY ANALYSIS (JSA) DI PT. KUNANGO JANTAN TAHUN 2016. Diploma thesis, Universitas Andalas.
|
Text (ABSTRAK)
ABSTRAK E-SKRIPSI ANDIO.pdf - Published Version Download (53kB) | Preview |
|
|
Text (BAB I)
BAB I ANDIO.pdf - Published Version Download (144kB) | Preview |
|
|
Text (BAB AKHIR)
BAB Akhir ANDIO.pdf - Published Version Download (54kB) | Preview |
|
|
Text (DAFTAR PUSTAKA)
Daftar Pustaka ANDIO.pdf - Published Version Download (47kB) | Preview |
|
Text (TUGAS AKHIR ILMIAH UTUH)
SKRIPSI TA UTUH ANDIO.pdf - Published Version Restricted to Repository staff only Download (2MB) |
Abstract
FAKULTAS KESEHATAN MASYARAKAT UNIVERSITAS ANDALAS Skripsi, Oktober 2016 ANDIO RAHMAN, No. BP. 1210333011 PENILAIAN RISIKO PEKERJAAN PADA DIVISI PIPA MENGGUNAKAN METODE JOB SAFETY ANALYSIS (JSA) DI PT. KUNANGO JANTAN TAHUN 2016 xi + 82 halaman, 39 tabel, 3 gambar, 5 lampiran ABSTRAK Tujuan Penelitian Kecelakaan kerja merupakan kejadian yang masih sering terjadi. Namun PT. Kunango Jantan belum juga melakukan identifikasi, penilaian dan, pengendalian risiko sebagai salah satu upaya mengurangi kecelakaan kerja. Penelitian ini bertujuan untuk mengetahui identifikasi bahaya, penilaian, dan pengendalian risiko di PT. Kunango Jantan Tahun 2016. Metode Penelitian ini merupakan penelitian kualitatif. Dilakukan pada bulan Juni sampai September tahun 2016 di tujuh bagian Divisi Pipa PT. Kunango Jantan yaitu Bagian Sliting, Bagian Uncoiling, Bagian Accumulating, Bagian Forming and Sizing, Bagian Cutting, Bagian Chamfering, dan Bagian Packing. Data primer diperoleh dari observasi di lapangan dan data sekunder diperoleh dari arsip perusahaan. Pendekatan yang digunakan adalah Job Safety Analysis dengan tiga tahapan yaitu identifikasi bahaya, penilaian, dan pengendalian risiko. Hasil Berdasarkan hasil penelitian, dapat disimpulkan bahwa di tujuh Bagian Divisi Pipa PT. Kunango Jantan terdapat risiko tinggi sebanyak 13 risiko tinggi, risiko sedang sebanyak 28 risiko dan risiko rendah sebanyak 5 risiko. Risiko-risiko ini belum sepenuhnya dapat dikendalikan oleh perusahaan sehingga masih menimbulkan kecelakaan kerja. Kesimpulan Terdapat sumber bahaya lingkungan kerja, pekerjaan manual, mekanik, fisik, dan faktor manusia. Risiko tinggi terdapat pada Bagian Sliting, Uncoiling, Forming and Sizing, Cutting, Chamfering, dan Packing. Pengendalian yang dilakukan belum terlaksana dengan baik. Disarankan kepada perusahaan agar segera melakukan tindakan pengendalian yang direkomendasikan agar kecelakaan dapat dihindarkan. Daftar Pustaka : 22 (1996-2016) Kata Kunci : Job Safety Analysis, Identifikasi Bahaya, Penilaian Risiko, Pengendalian Risiko FACULTY OF PUBLIC HEALTH ANDALAS UNIVERSITY Undergraduate Thesis, October 2016 ANDIO RAHMAN, No. BP. 1210333011 THE RISK ASSESSMENT OF OCCUPATIONAL SAFETY AT PIPE DIVISION USING JOB SAFETY ANALYSIS (JSA) AT PT. KUNANGO JANTAN 2016 xi + 82 pages, 39 tables, 3 pictures, 5 appendices ABSTRACT Objective Work accident is an event that is still common. But PT. Kunango Jantan yet to make the identification, assessment and risk control as an effort to reduce accidents. This study aims to determine the hazard identification, assessment and control of risk at PT. Kunango Jantan 2016. Method This research is qualitative. Conducted in June to September 2016 in the seven-part Pipe Division PT. Kunango Jantan namely Sliting, Uncoiling, Accumulating, Forming and Sizing, Cutting, Chamfering, and Packing Section. Primary data were obtained from field observation and secondary data obtained from the company archives. The approach used is a Job Safety Analysis with three stages namely hazard identification, assessment and risk control. Result Based on the results, it can be concluded that in the seven-part Pipe Division PT. Kunango Jantan high risks as much as 13 risks, medium risk as much as 28 risks and low risk as much as 5 risks.. These risks are not fully controlled by the company so that they still causes accidents Conclusion There is a source of danger working environment, manual handling, mechanical, Physic and human factor. High risk contained in Sliting, Uncoiling, Forming and Sizing, Cutting, Chamfering, and Packing Section. Control is done not done well. It is suggested to the company to immediately carry out control measures recommended in order that accidents can be avoided. References : 22 (1996-2016) Key Words : Job Safety Analysis, Hazard Identification, Risk Assessment, Risk Management.
Item Type: | Thesis (Diploma) |
---|---|
Subjects: | R Medicine > RA Public aspects of medicine > RA0421 Public health. Hygiene. Preventive Medicine |
Divisions: | Fakultas Kesehatan Masyarakat |
Depositing User: | s1 kesehatan masyarakat |
Date Deposited: | 27 Oct 2016 04:47 |
Last Modified: | 27 Oct 2016 04:47 |
URI: | http://scholar.unand.ac.id/id/eprint/18140 |
Actions (login required)
View Item |